Adtran Fiber Commands Adtran Fiber Command Generator Command Help SelectionNOTE: USE CAPITAL LETTERS IN SERIALS!Desired Output* command formatting only Action to be Taken* Check Status of an ONT Shut Off an ONT Shut Off Ethernet Port Remove / Replace an ONT Confirm Fiber Programming Reactivate an ONT Reactivate an Ethernet Port Clear MAC Address Remove ONT Speed Check Command Formatting HelpDescription Explanation help Yes Description Examples pretend that the following was the assignment information: ONT = ##ONT## = 53 Serial = ##SERIAL## = ADTN192129B1 CARD = ##CARD## = 02 PON = ##PON## = 03 Ethernet Port on ONT = ##EPORT## = 4 MAC Address = ##:##:##:##:##:## = 00:19:92:9F:83:24 Device/Card/PON: ONWAdtran1/##CARD##/##PON## = ONWAdtran1/02/03 PLACEHOLDER: Check Status by Serial#show table remote-devices | i ##SERIAL##example: show table remote-devices | i ADTN192129B1 PLACEHOLDER: Check Status by ONT/GPONshow table remote-devices ont ##ONT##@1/##CARD##/##PON##.gponexample: show table remote-devices ont 53@1/02/03.gponPLACEHOLDER: Confirm Fiber Programming / Assignmentshow remote-device ont ##ONT##@1/##Card##/##PON##.gponexample: show remote-device ont 53@1/02/03.gpon Returns with: SERIAL assigned Name & MST Status PLACEHOLDER: Step 1. Confirm Fiber Programming / Assignmentshow remote-device ont ##ONT##@1/##Card##/##PON##.gponexample: show remote-device ont 53@1/02/03.gpon Returns with: SERIAL assigned Name & MST Status PLACEHOLDER: Step 1. Show EVC-MAPshow evc-map PON##PON##-ONT##ONT##-Port01Example: show evc-map PON03-ONT53-Port01 Once you enter command, hit the space bar until there are no more ---MORE--- You will see something similar to: MAC Address IPv6 Address State --------------------------------------- ---------- 00:19:92:9F:83:24 FE80::219:92FF:FE9F:8324 IPv6 LinkL 00:19:92:9F:83:22 FE80::219:92FF:FE9F:8322 IPv6 LinkL 88:3D:24:6F:D5:94 FE80::8A3D:24FF:FE6F:D594 IPv6 LinkL Choose the one to remove then go to the next step Directory: conf t PLACEHOLDER: Step 2. Remove ONT Programmingno remote-device ont ##ONT##@1/##Card##/##PON##.gponexample: no remote-device ont 53@1/02/03.gpon PLACEHOLDER: Shut Off ONTremote-device ont ##ONT##@1/##Card/##PON##.gpon shutdownExample: show table remote-devices ont 53@1/02/03.gpon shutdownPLACEHOLDER: Shut Off Ethernet Portinterface gigabit-ethernet ##ONT##/0/##EPORT##@1/##Card##/##PON##.gpon shutdownExample: interface gigabit-ethernet 53/0/4@1/02/03.gpon shutdownPLACEHOLDER: Reactivate ONTremote-device ont ##ONT##@1/##Card##/##PON##.gpon no shutdownExample: remote-device ont 53@1/02/03.gpon no shutdown PLACEHOLDER: Reactivate Ethernet Portinterface gigabit-ethernet ##ONT##/0/##EPORT##@1/##Card##/##PON##.gpon no shutdownExample: interface gigabit-ethernet 53/0/4@1/02/03.gpon no shutdownPLACEHOLDER: Step 1. Shut Off ONT & Remove Serial Numberremote-device ont ##ONT##@1/##Card/##PON##.gpon shutdown no serial-number "##Serial##"Example: show table remote-devices ont 53@1/02/03.gpon shutdown no serial-number ADTN192129B1PLACEHOLDER: Step 2. Assign New Serial Numberremote-device ont ##ONT##@1/##Card##/##PON##.gpon shutdown serial-number "##Serial##" no shutExample: show table remote-devices ont 53@1/02/03.gpon shutdown no serial-number ADTN192129B1PLACEHOLDER: Step 2 Clear MAC Addressclear mac address-table 1/##CARD## address ##:##:##:##:##:##clear mac address-table 1/02 address 00:19:92:9F:83:24PLACEHOLDER: Speed Checksh shaper PON##-ONT##-up sh shaper PON##-ONT##-downFind the PON - see prg for: Device01/Card/PON Replace ONT "##" with the ONT ID assignment Example if ONT status was: 32@1/1/5.gpo IS up ADTN2014B733 4026 -20.0 1.7 0 0 0 Then PON## = PON05 and ONT## = ONT32 HiddenRequired PerametersHiddenDevice Always 01HiddenCard/OLT* ##Card## = card, 2 digit with leading 0 if necessary, for example 01 or 02 or 03 or … HiddenPON* ##PON## = port, 2 digit with leading 0 if necessary, for example 01 or 02 or 03 HiddenSerial* ADTN???????? HiddenONT* ##ONT## = number of ont, 2 digit with leading 0 if necessary, for example 06, or 23 HiddenFormatting Info * Open Putty: * Select correct Fiber Switch * Login & Password * Type: show table remote-devices inactive NOTE: USE CAPITAL LETTERS IN SERIALS!